![](/uploads/1/2/7/5/127562103/539747836.png)
Click on photo forlarger viewRevisit™VTL5C1 OPTO-ISOLATORReplaces VTL5C1 from Vactec or Excelitas at anaffordable price. Used in many Mesa-Boogie and Crate models in the channelswitching circuit.
100dB dynamic range, fast response (2.5msturn-on), very high dark resistance (50 M Ohm). Light resistance 200 Ohmsat 20mA LED current.
See datasheet.Part # VTL5C1$4.95Click on photo forlarger view10-ConductorRibbon Cable, 3 inches longUsed to interconnect circuit boards in a variety of amps. 3 inches long. 10 conductors set at 0.1 inch spacing - complete cable is 1 inch wide. Bare wire termination for soldering to PC board at 0.1' hole spacing - noconnectors.
May be easily cut with an X-Acto knife to make a cable of fewer than 10conductors. Not recommended for use in the Fender Hot Rod Deluxe /Deville or Blues Deluxe / Deville. The ribbon cables used in those amps haveribbon cables with conductors set at 0.156' spacing - this cable is too narrowfor that application.Part #RJ-310$0.99Ampeg® & Crate HardwareClick on photo forlarger viewL-PAD FACE PLATE AND KNOB, for 3/8' diameter threaded bushing found on most L-Pad Levelcontrols. Face plate AND knob only!
L-Pad ordered separately.Fits many basscabinets including the SWR Goliath, Marcus Miller Golight 410, Workingman8x10, Working Pro 2x10, Ampeg PN-210HLF, PN-410HLF, SVT-410HLF, SVT-610HLF,SVT-810SPC, BXT210M,BXT410HL4, PR-1528HE, PN-115HLF, PR-810H, PB-250, the Kustom G410H, theEngl B115 as well as many others.This is the face plate and knob only - L-PAD itself ordered separately.Raised lettering in charcoal gray instead of white. 3 1/8 inches indiameter, 7/8 inch depth into cabinet. Requires 2 inch diameter holefor mounting. Screws not included.Part #LFP-380$3.998 OhmsClick on photo forlarger viewL-PAD, 8 Ohms, 3/8' threaded bushing (3/8' long), with plate, knob and hardware.May also be used with the LFP-380 face plate and knob.
Valuation Report for Used SVT-15T Bass Amplifier by Ampeg (Specs: 100 Power (Watts/Ohms), (1) 15').
![Ampeg svt repair Ampeg svt repair](http://ampbroker.pl/5003-thickbox_default/ampeg-svt-15t.jpg)
8 ohms- for use with 8 ohm speakers, horn drivers or tweeters.L-pads adjust the relative volume of drivers connected to them by placing addedresistance in series and parallel, keeping impedance a constant 8 ohm load. ThisL-pad is rated at 100 watts RMS, is designed to be used with 8 ohm loads,features a 3/8' shaft length, and comes with mounting hardware.
Thisstyle of L-Pad is found on many popular bass cabinets to control thehorn/tweeter level. 2.5 inches in diameter, 1 inch thick.Included face plate is 2 1/8' x 2 1/8'.Part #LPD-2 OhmsClick on photo forlarger viewL-PAD, 16 Ohms, 3/8' threaded bushing (3/8' long), with plate, knob and hardware.May also be used with the LFP-380 face plate and knob. 16 ohms - foruse with 8 ohm speakers, horn drivers or tweeters.L-pads adjust the relative volume of drivers connected to them by placing addedresistance in series and parallel, keeping impedance a constant 8 ohm load. ThisL-pad is rated at 100 watts RMS, is designed to be used with 16 ohm loads,features a 3/8' shaft length, and comes with mounting hardware.
Thisstyle of L-Pad is found on many popular bass cabinets to control thehorn/tweeter level. 2.5 inches in diameter, 1 inch thick.Included face plate is 2 1/8' x 2 1/8'.Part #LPD-261$17.95Click on photo forlarger viewAmpeg® 'a' LogoUsed on modern Ampeg Speaker Cabinets, this 3 inch x 4 inch plastic logo isaffordably priced. Mounting screws not included.Use LS-504 for mounting screws.Mounting centers are2 ¼' x 2 ⅜'.Part #AL-921$4.95Click on photo forlarger viewBlack Logo Mounting ScrewsSet of 4 logo mounting screws.These are #5 x 7/16' black oxidescrews, set of 4. Fit the AL-921 Ampeg logo, and the FenderFAL-912 logo.Part #LS-504$0.99(for a set of 4 screws)Click on photo forlarger viewTUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34.Used in many different amplifier brands. 1 1/2' Mounting Centers.Part #TC-142$1.79Click on photo forlarger viewLARGE TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6550 OR KT-88 TUBES.Part #TC-143$2.99Click on photo forlarger viewTUBE SHIELD, BAYONET 'PUSH AND TWIST' TYPE, ALUMINUM, 1 15/16' TALLWITH 9-PIN TUBE SOCKET AND INTEGRAL TUBE SHIELD BASE.
Spring in top of shield fits over thetube. Fits 12AX7A and similarly sized preamp tubes. 9-Pin tubesocket is made of sturdy Micalex. Replacement for Fender® and many other brands. Holes in base spaced 1 1/8' apart.Requires 3/4' hole in chassis. Solder lugs for wire connection to tubesocket.Shield, base and socket.Part #TS-370$3.99Click on photo forlarger viewTUBE SHIELD, BAYONET 'PUSH AND TWIST' TYPE, ALUMINUM, 1 15/16' TALL.Includes new base, if needed.
Spring in top of shield which fits over thetube. Fits 12AX7A and similarly sized preamp tubes. Replacement for Ampeg,Crate and many other brands. Holes in base spaced 1 1/8' apart.Shield and base only - socket not included.Part #TS-325S$1.69Click on photo forlarger viewTUBE SHIELD, BAYONET 'PUSH AND TWIST' TYPE, ALUMINUM, 1 15/16' TALL,SET OF 6.Includes new bases, if needed.
Spring in top of shield fits over the tube.Fits 12AX7A and similarly sized preamp tubes. Replacement for Ampeg, Crate, and manyother brands. Holes in base spaced 1 1/8' apart. Shield andbase only - socket not included.Part #TS-325S-6$8.95(TUBE NOT INCLUDED)Click on photo forlarger viewRevisit™ PRE-AMP TUBE DAMPERRINGS.Use two (or three) of these rings around a pre-amp tube to reduce noise andmicrophonics. An economical alternative to more expensive tube dampers.Will withstand high temperatures of pre-amp tubes, reusable when you changetubes.
Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes. Thesedampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5.Part #PTD-6$2.99(Set of 6 rings)Click on photo forlarger viewGround Lug Terminals - AngledMade from tin-plated brass - will not rust. Used to connect a ground wire to a screw and nut on a chassis.Angled,with two holes for soldering wires.
With built-in lock washer to keep the screwand nut from loosening. Designed for a #8 size screw.Pack of 5 terminals.Part #GL-113$1.39(Pack of 5 terminals)Click on photo forlarger viewTERMINAL STRIPS, 6 LUG, SET OF2. Perfect for amplifier circuit additions or modifications.Center post for mounting to chassis. All 6 terminals are isolatedfrom ground. Each terminal strip is 2-5/8 incheslong. The lugs are set on 3/8 inch centers. Each lugwill accept wires up to 16ga - smaller gauge allows multiple wires to beconnected to each lug.
Set contains 2 terminal strips as pictured.Mounting hardware not included.Part #TS-825$2.89(for a set of 2 terminal strips)Click on photo forlarger viewTERMINAL STRIPS, 7 LUG, SET OF2. Perfect for amplifier circuit additions or modifications.End terminals on each strip are the mounting lugs, so they become a ground lugif attached to a metal chassis. Each terminal strip is 2-5/8 incheslong.
The lugs are set on 3/8 inch centers. Each lugwill accept wires up to 16ga - smaller gauge allows multiple wires to beconnected to each lug. Set contains 2 terminal strips as pictured.Mounting hardware not included.Part #TS-712$3.29(for a set of 2 terminal strips)Click on photo forlarger viewCUP WASHER, BLACK METAL, PACK OF 10. USED WITH #8 BLACK SCREW ON AMP AND SPEAKER CABINETS.Part #BCW-10$1.29(pack of 10)Click on photo forlarger viewSPEAKER BAFFLE MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 4. Lockingnut and washer included. Phillips head.
Drill hole, insert andtighten screws into wood from front of baffle. Install grill cloth, andyou have professional speaker mounting studs. Replacement fororiginal Fender® speaker mounting studs. Set of 4.Part # SC-409-4$4.50(For a pack of 4 screws with nuts and lock washers)Click on photo forlarger viewISOLATION WASHER - 3/8' - For #8 Screws3/8' outside diameter neoprene bonded flat washer.
Perfect forbolting speakers to cabinets. It will securely hold the speaker in place andstop any rattling.
For use with #8 screws. Ideal for vintage Fenderamps with #8 speaker mounting screws. Set of 4 washers.Part #SIW-38-4$0.59(For a set of 4 washers)Click on photo forlarger viewISOLATION WASHER - 1/2' - For #10 ScrewsLarger 1/2' outside diameter neoprene bonded flat washer. Perfect forbolting speakers to cabinets. It will securely hold the speaker in place andstop any rattling. For use with #10 screws, such as a 10-32 machine screw.
Set of 4 washers.Part #SIW-50-4$0.69(For a set of 4 washers)Click on photo forlarger viewBLACK PAN-HEAD WOOD SCREWS, #6 X 3/4', PACK OF 10. Deepthreads, sharp point, pan head with Philips drive. #6 screw, 3/4 inchlong, pack of 10.Part #SCR-435$0.79(pack of 10)BLACK PAN-HEAD WOOD SCREWS, #8 X 1/2', PACK OF 10. Deepthreads, sharp point, pan head with Philips drive.
#8 screw, 1/2 inchlong, pack of 10.Part #BWS8-5$0.89(pack of 10)BLACK PAN-HEAD WOOD SCREWS, #8 X 3/4', PACK OF 10. Deepthreads, sharp point, pan head with Philips drive. #8 screw, 3/4 inchlong, pack of 10.Part #BWS8-75$0.95(pack of 10)BLACK PAN-HEAD WOOD SCREWS, #8 X 1', PACK OF 10.
Deepthreads, sharp point, pan head with Philips drive. #8 screw, 1 inch long,pack of 10.Part #BWS8-1$1.05(pack of 10)BLACK PAN-HEAD WOOD SCREWS, #8 X 1 1/2', PACK OF 10.Deep threads, sharp point, pan head with Philips drive. #8 screw, 1-1/2inches long, pack of 10.Part #BWS8-15$1.19(pack of 10)Click on photo forlarger viewCAGE NUT, ZINC, 10-32THREAD. Used on square-punched amp chassis rails to secure thechassis to the cabinet.
Frequently found in Peavey, Crate, Ampeg,other brands. NOT used in Marshall® - see the MCN-4. Works with all10-32 screws.Verify screw thread before ordering, as not all cage nuts are 10-32. Zinc coating retards oxidation.Pack of 4 nuts.
Made in Canada by Hammond Industries.Part CNA-1421$4.29(pack of 4)Click on photo forlarger viewSMALL BLACK RUBBER FEET, SET OF 4This 4-pack of heavy-duty rubber feet offers a sure gripon all types of surfaces. Ideal for smaller amps, amp heads, effects units,larger floor effects pedals, or speakercabinets. The integral metal washer in the mounting hole helps preventmounting screw 'break-through' and adds overall durability.0.84'diameter x 0.31' high. Screws not included.
Set of 4feet.Part #BRF-750 - Currently out of stock. More on the way, expected to arrive May 5.$2.95(pack of 4)Click on photo forlarger viewSMALL BLACK RUBBER FEET, SET OF 4.This heavy-duty rubber foot offers a sure gripon all types of surfaces. Ideal for smaller amps, amp heads, or speakercabinets. The integral metal washer in the mounting hole helps preventmounting screw 'break-through' and adds overall durability.Just under 1 inch - 15/16'diameter at the top, rounded down to 5/8' diameter at the bottom, and 3/8'tall. Screws not included. Set of 4feet.Part #BRF-723$3.95(pack of 4)Click on photo forlarger viewMEDIUM BLACK RUBBER FEET, SET OF 4. This heavy-duty rubber foot offers a sure gripon all types of surfaces.
Ideal for amp heads, combo amps, or smaller speaker cabinets.the integral metal washer in the mounting hole helps prevent mounting screw'break-through' and adds overall durability. 1' diameter x5/8' tall.
Mountingscrews not included. This set of 5 works well for the main feetused on the Ampeg BA-210 when the cabinet is in the upright position.Part #BRF-1692-5$6.25(pack of 5)Click on photo forlarger viewMEDIUM BLACK RUBBER FEET, SET OF 4. Tapered: 1 3/16' DiameterAt Small End, 1 1/4' Diameter At Large End. Black Rubber With MetalInsert. Used To Support Effects, Amps, Mixers. Mounting Screws Not Included.Part #BRF-9112$4.95(pack of 4)Click on photo forlarger viewX-LARGE BLACK RUBBER FEET, SET OF 4.Tapered - 1 5/8' Diameter At Large End, 1 1/4' At Small End. BlackRubber With Metal Insert.
Used To Support Amp Heads, Speaker Cabinets. MountingScrews Not Included.Part #BRF-9107$7.95(pack of 4)Click on photo forlarger viewFender® Style Flat Mount 2' Caster Wheels - Setof 4.Great for Fender® and many other brands of amps or cabinets.
Eachwheel capable of supporting 45 lbs, or 180 lbs total for the set of 4.Wheels 2' in diameter. Specifications found. Note:Mounting screws NOT included.Part #FCW-4F$24.95(Set of 4 casters)NOTSOLD OUTSIDE the USAClick on photo forlarger viewFender® Style Pop-Out 2' Caster Wheels - Setof 4.Great for Fender® and many other brands of amps or cabinets. Eachwheel capablesupporting 45 lbs, or 180 lbs total for the set of 4.
Wheels 2' indiameter. The same type of removable caster wheels used on Fender® ampssince the 1960s. Note:Mounting screws NOT included. Must drill 5/8' hole in bottom ofcabinet to accommodate post for wheel.Part #FCW-4R$29.95(Set of 4 pop-out casters)NOT SOLD OUTSIDE the USAClick on photo forlarger viewRevisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, BLACK WITHBLACK STITCHINGGood replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera,Blackstar, many others. Handlelength is 8-9/16 inches (8.57'), center-to-center mounting distance is 7-3/8inches (7.38') Black with black stitching, nickel mounts.Mountingscrews not included - use SC-402 screw pack.Part #AH-281$12.95' SHORTY' AMP HANDLEClick on photo forlarger viewRevisit™' SHORTY' AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, BLACK WITHBLACK STITCHINGSimilar to the AH-281 handle above, but 1-3/4 inches shorter.
Handlelength is 6-13/16 inches (6.80'), center-to-center mounting distance is 6inches (5.98') Black with black stitching, nickel mounts. Mountingscrews not included - use SC-402 screw pack. This is a great handleto consider for smaller combo amps, practice amps, etc. Delivers aprofessional quality look and reliability in a smaller size for smaller amps.Part #AH-281-S'Shorty'$10.95Click on photo forlarger viewRevisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, DARK BROWN WITHBROWN STITCHINGGood replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera,Blackstar, many others.
Handlelength is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8inches (7.38') Dark brown with brown stitching, nickel mounts.Mountingscrews not included - use SC-402 screw pack.Part #AH-270$12.95Click on photo forlarger viewRevisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE,TAN WITH TAN STITCHINGGood replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera,Blackstar, many others. Handlelength is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8inches (7.38') Tan with tan stitching, nickel mounts.Mountingscrews not included - use SC-402 screw pack.Part #AH-108$12.95Click on photo forlarger viewRevisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, DARK BROWN WITHWHITE STITCHINGGood replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera,Blackstar, many others. Handlelength is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8inches (7.38') Dark brown with white stitching, nickel mounts.Mountingscrews not included - use SC-402 screw pack.Part #AH- 318$12.95Click on photo forlarger viewRevisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, DEEP NAVY BLUE-GREY WITHWHITE STITCHINGGood replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera,Blackstar, many others. Handlelength is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8inches (7.38') Dark navy blue-grey with white stitching, nickel mounts.Mountingscrews not included - use SC-402 screw pack.Part #AH- 319$12.95Click on photo forlarger viewFender® or Ampeg® VINTAGE STYLE GUITAR AMP HANDLE, RAISED,BLACK STITCHEDSIMULATED LEATHER. Black handle strap, made of simulated leather,replacement for Fender® 'tweed' style amps or vintage Ampeg amps (as well asother vintage amps. Has slight 'raised' bump near the center of the handle.Black, white stitched.
6-1/4 to 6-1/2 inches between mounting posts. Total length 8-3/4'. Mounts and screwsare included.Part #GAH-782$15.95Click on photo forlarger viewRevisit™ BLACK GUITAR AMP HANDLE,WITH HARDWARE.Rugged rubber black handle strap, steel reinforced. Black metal caps.Black 10-32 screws and T-Nut mounting hardware are included.
Handle strap is 7/8'wide. Designed for screw holes set 8 1/4 to 8 3/8 inches apart. Total length of handle when properly mounted is10 1/4'.Part #GAH-271B$7.99Click on photo forlarger viewRevisit™ GUITAR AMP HANDLE- BLACK.Rugged rubber black handle strap, steel reinforced. Black metal caps.Screws not included - recommend using our SC-403B 10-32 type screws along with a10-32 T-Nut for secure mounting.
Handle strap is 7/8' wide.Designed for screw holes set 8 1/4 to 8 3/8 inches apart. Totallength of handle when properly mounted is 10 1/4'.Part #GAH-1$6.99Click on photo forlarger viewBLACK HANDLE SCREWSPack of 2 stainless-steel handle screws finishedin satin black for usewith black end-cap handles, such as our GAH-1, OAH-456, or GAH-271B. 1-1/4' Long, 10-32 threads, finished in satin black to match black end caps. Designedto work with a 10-32 T-Nut, in cabinet wood of 3/4' or less.Will not work with external nut - must be a T-Nut. Will not workwith cabinet wood thicker than 3/4'.Part #SC-403B$0.99(for a pack of 2 screws)Click on photo forlarger viewRevisit™ CHROME/BLACK GUITAR AMP HANDLE- CHROME, WITH HARDWARE.Rugged rubber black handle strap, steel reinforced.
Chrome metal caps.10-32 screws and T-Nut mounting hardware are included. Handle strap is 7/8'wide. Designed for screw holes set 8 1/4 inches apart. Total length of handle when properly mounted is10 1/4'.Not recommended for Fender, as the screws are set too far apart forFender® amp specifications.Part #GAH-271C$7.99Click on photo forlarger viewHANDLE SCREWSPack of 2 stainless steel handle screws forGAH-271C Handle. 1' Long, 10-32 threads. Designedto work with a 10-32 T-Nut, in cabinet wood of 3/4' or less.Will not work with external nut - must be a T-Nut. Will not workwith cabinet wood thicker than 3/4'.Part #SC-403$0.99(for a pack of 2 screws)Click on photo forlarger viewLARGE SIZED STRAIN RELIEF FOR 35/64' X 5/8' HOLEPopular strain relief found on mostvintageguitar amplifiers with round power cords.
Designed for 5/16' cord diameter.for specific dimensions of chassis hole.For a strain relief removal / installation tool to make the job much easier,see the YTH-205 below.Part # SR-1200$0.99Click on photo forlarger viewSTRAIN RELIEF INSTALLATION/REMOVAL TOOLRemoving and installing a strain relief can be a frustrating job.Standard pliers just do not get the job done and can damage the strain relief.These special strain relief pliers are just what you need. They fitperfectly on the AC power cord strain relief and give you the leverage you need tocompress the strain relief for easy removal and installation, without damage.Part #YTH-205$12.95(Factory currently shut down due to COVID-19. Availabilitydate for this item is unknown.)Click on photo forlarger viewEXTRA-LARGE SIZED STRAIN RELIEF FOR 3/4' X27/32' HOLEPopular strain relief found ona fewlarger vintage bass amplifiers and power amplifiers with very thick power cords. Designed for 11/32' cord diameter.for specific dimensions of chassis hole.Part # SR-1300$0.99Click on photo forlarger viewSMALL RUBBER CHASSIS GROMMET FOR 3/8 INCHCHASSIS HOLE (GROMMET INNER HOLE 1/4 INCH)Chassis grommet, forelectrical insulation, wire protection and management, shock absorption, ormechanical isolation.
This grommet has a 1/4 inch diameter inner hole,and mounts in a 3/8 inch chassis hole.Part #RCG-739$0.49eachClick on photo forlarger viewLARGE RUBBER CHASSIS GROMMET FOR 1/2' CHASSIS HOLE(GROMMET INNER HOLE 3/8 INCH)Chassis grommet, forelectrical insulation, wire protection and management, shock absorption, ormechanical isolation. This grommet has a 3/8 inch diameter inner hole,and mounts in a 1/2 inch chassis hole.Part #RCG-745$0.49eachAmpeg FansClick on photo forlarger viewThermoCool Fan. 80 x 38mm Sleeve Bearing19 CFM.Thermocool axial fans provide enhanced cooling for a variety of electronicdevices. Leading air flow technology is designed into every thermocool productresulting in reduced turbulence, low noise levels and a more energy efficientproduct. Thermocool fans are ideal for use in computer systems, portable CD andDVD players, stereo components, overhead projectors, laptop computers, and manyother electronic applications where circulation is a key concern.This fan is the replacement for the fan used in the Ampeg SVT Classic, Ampeg®part number 24-321-03.
Specifications:. Power: 120VAC, 60 Hz.
Sleeve bearing. Lead wire connection.
0.13 amps. 2400 RPM.28dB noise level. 23 CFM air flow. Dimensions: 80 mm (H) x 80 mm (W) x 38mm (D)3 1/4' (H) x 3 1/4' (W) x 1 1/2' (D) For use on110-120VAC System only, as found in North America.Part #G8038HAS$19.95Ampeg® & Crate®JacksClick on photo forlarger viewJACK, 1/4',CHROMENUT, CLOSED CIRCUIT, PC MOUNT, L-LEG, TIP-SLEEVE, 4 PINS.Generally found only inCrate or Ampeg products. Common input, footswitch oreffects loop jack exclusive to Crate® and Ampeg®.(Other brands with chrome-nut jacks use a straight pin jack such as the J-580.)4 pins, PC mount, withchrome nut and washer. Note 'L-Leg' pins as shown in photo.Original Crate or Ampeg part number 39-119-01.Part #J-580L$3.95Click on photo forlarger viewJACK, 1/4', CHROMENUT, CLOSED CIRCUIT, PC MOUNT, GENUINE CLIFF UK, L-LEG, TIP-RING-SLEEVE, 6 PINS.Generally found only inCrate or Ampeg products. Common input, footswitch or effects loop jack exclusive to Crate®, Ampeg®.(Other brands with chrome-nut jacks use a straight pin jack such as the J-581.) 6 pins, PC mount, withchrome nut and washer.
Note 'L-Leg' pins as shown in photo.Original Crate or Ampeg part number 39-120-01.Part #J-581L$4.50Click on photo forlarger viewJACK, 1/4', INPUT, CLOSEDCIRCUIT, PC MOUNT, L-LEG, TIP-SLEEVE, 4 PINSCommon input jack in Crate®, Ampeg®, others. Ampeg and Crate®part number 39-116-01.
4 pins, PC mount, with nut and washer. Note'L-Leg' pins as shown in photo.Part #J-503L$3.79Click on photo forlarger viewJACK, 1/4', INPUT, CLOSEDCIRCUIT, PC MOUNT, L-LEG, TIP-RING-SLEEVE, 6 PINCommon input jack in Crate®, Ampeg®, others.
Ampeg and Crate partnumber 39-117-01. 6 pins, PC mount, with nut and washer. Note'L-Leg' pins as shown in photo.Part #J-504L$3.95Click on photo forlarger viewJACK NUT, PLASTIC,BRITISH CLIFF STYLE, REPLACEMENT FOR Marshall® AND OTHERS.Note: Replaces most black plastic jack nuts EXCEPT forRoland. Will NOT fit Roland jacks.Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L andJ-504L jacks. Also fits the J-518 and J-519 jacks.Part #J-5NT$0.50Click on photo forlarger viewJACK NUT MULTI-PACK - SAVE! 6 JACK NUTS, PLASTIC,BRITISH CLIFF STYLE, REPLACEMENT FOR Marshall® AND OTHERS.Note: Replaces most black plastic jack nuts EXCEPT forRoland.
Will NOT fit Roland jacks.Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L andJ-504L jacks. Also fits the J-518 and J-519 jacks.Part #J-5NT-6$2.39Click on photo forlarger viewJACK NUT/FERULE, CHROME,with BLACK PLASTIC BEZEL/WASHER - GENUINE CLIFFUKReplacement nut and bezel washer for the J-501, J-501S, J-580, J-581, J-580L and J-581L jacks.Note: The threads on this nut are coarse (3/8-20), and are forgenuine Cliff jacks. Note:There are some generic jacks on themarket with finer thread nuts.This nut will not fit those jacks. This nut is forgenuine Cliff UK jacks.
Bezel isincluded with this nut.Part #JN-200W$0.79Click on photo forlarger viewJACK NUT/FERULE,BLACK,with INTEGRAL BLACK PLASTIC BEZEL - GENUINE CLIFFUKReplacement nut and bezel washer which will fit the J-501, J-501S, J-580, J-581, J-580L,and J-581L jacks.Note: The threads on this nut are coarse (3/8-20), and are forgenuine Cliff jacks. Note:There are some generic jacks on themarket with finer thread nuts.This nut will not fit those jacks. This nut is forgenuine Cliff UK jacks. Bezel is integral to the nut and cannot beremoved. This is the jack nut used on the Marshall JMP-1 Preamp, andon some versions of the Marshall DRP-1 Direct Recording Preamp.Part #JN-864$0.79Click on photo forlarger viewJACK, 1/4', PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED.Both tip and ringconductors are switched (normally closed). Used in Peavey® and other brands.
Same as J-523, except that the pins are smaller for insertion into smaller PC holes. Nut and washer included.Part #J-527$4.50JACK NUT AND WASHER, METAL,SWITCHCRAFT®Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and theCTS or Alpha pots with 3/8' bushing (found on original vintage Fender®blackface and silverface), as well as Peavey® and Switchcraft®1/4' jacks.
Does NOT fit the 24mm Marshall® pots.Part #JNUT-38$0.89(Set of 1 washer and 1 nut)Click on photo forlarger viewDual Chassis-Mount Banana BindingPosts. Used on the rear panel of many power amplifiers and somebass amps, such as the Ampeg B4R. Red and black posts, accepts eithersingle or dual banana plugs. Mounts in two 1/2' holes on 3/4' centers, panelthickness up to 1/4'. 15A rating, gold plated contacts.Part #BP-263$4.99Click on photo forlarger viewJACK, 1/4', MONO, OPEN CIRCUIT,WIRED, Switchcraft ®Found in many guitars, effects pedals, amps speaker output. Includesnut and washer.Part #J-11$2.25Click on photo forlarger viewJACK, 1/4', MONO, CLOSED CIRCUIT(SHORTING), WIRED, Switchcraft ®Found in vintage amps as the input jack.
Includes nut andwasher.Part #J-12A$2.79Click on photo forlarger viewJACK, 1/4', TIP-RING-SLEEVE, OPENCIRCUIT, WIRED, Switchcraft ®Used with T/R/S plugs for either balanced connections or stereo connections.Also very common in guitars with active pickups, and as the input jack on someeffects pedals. The ring conductor is used in these cases to 'turnon' the battery by tying one leg of the battery to ground via the plug.Part #J-12B$2.99Click on photo forlarger viewJACK, 1/4', TIP-RING-SLEEVE, OPENCIRCUIT, WIRED, Switchcraft ®,LONG BUSHINGSame as the J-12B jack, but with longer (3/8') threaded bushing for mountingin thicker panels. Includes nut and washer.Part #J-L12B$3.99Click on photo forlarger viewJACK, 1/4', TIP/RING/SLEEVE, WITHTIP SHUNT. Switchcraft 13B Jack.Tip/Ring/SleeveSwitchcraft jack. Tip has a shunt contact, ring contact is opencircuit.Part #J-13 B$6.95Click on photo forlarger viewJACK, 1/4', MONO, CLOSED CIRCUIT, RIGHT ANGLE PC MOUNT, Switchcraft ®STYLE, NYLON THREADS,3 PINSCommon input jack in Crate ® & Ampeg ®,and in some solid state products from Fender ®during the early 1980s. Nut and washer included.Part # RN112APC$5.79Click on photo forlarger viewJACK, 1/4', STEREO, CLOSED CIRCUIT, RIGHT ANGLE PC MOUNT, Switchcraft ® STYLE, NYLON THREADS, 5 PINSCommon input jack in Crate ® & Ampeg ®products.
Nut andwasherincluded. Switchcraft RN114BPC. Nut and washer included.Part #J-114PC$5.99Click on photo forlarger viewSAVE WITH MULTIPACK!JNUT-38 JACK NUT AND WASHER, METAL,SWITCHCRAFT®, SET OF 6Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and theCTS or Alpha pots with 3/8' bushing (found on original vintage Fender®blackface and silverface), as well as Peavey® and Switchcraft®1/4' jacks. Does NOT fit the 24mm Marshall® pots.
Set of6 washers and 6 nuts.Part #JNUT-38-6$4.50(Set of 6 washers and 6 nuts)JACK NUT AND WASHER, METAL,SWITCHCRAFT®Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and theCTS or Alpha pots with 3/8' bushing (found on original vintage Fender®blackface and silverface), as well as Peavey® and Switchcraft®1/4' jacks. Does NOT fit the 24mm Marshall® pots.Part #JNUT-38$0.89(Set of 1 washer and 1 nut)Click on photo forlarger viewAvailable with or without nut andwasher.JACK, 1/4', TIP/RING/SLEEVE, 7 PIN, PC MOUNT,Fender ®,Hartke ®,B-52 ®,Randall ®,and Crate ®Amps.Fender®, Hartke®, Randall®, B-52® or Crate® PCB mount 1/4' jack.7 pins. Fits several Hartke ® amp models 1990- present, and several Crate ® models, especially in the GX series. Usedin the Fender ® SKX65R and SKX100R for the inputjacks.Used in some Fender ®Squier and Sidekick amps as the headphone jack.
Replaces Hartke ®part number 350023 and 300519. ReplacesFender ®part number 022923. Replacement nut/washer set is the JN-916.Available with or without nut/washer - choose in 'Options'Part # J-545Starting at$5.95Select Option:Quantity:NUT AND WASHER, CHROME, KOBICONNOR JALCO TYPE.Fits J-506, J-506A, J-507, J-530, J-531G, J-532, J-532G, J-533, J-533G,J-539, J-539G, J-540, J-545, J-6074, J-6075, J-560.Part #JN-916$0.75Click on photo forlarger viewJACK, 1/4', PC MOUNT, STEREO, 5 PINS, SWITCHED, METAL BUSHING.Both tip andring conductors are switched (normally closed). Replaces Switchcraft 114BPCX and 114BPCSX. Nut and washer included.Part #J-529$3.50Click on photo forlarger viewSAVE WITH MULTIPACK!JNUT-38 JACK NUT AND WASHER, METAL,SWITCHCRAFT®, SET OF 6Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and theCTS or Alpha pots with 3/8' bushing (found on original vintage Fender®blackface and silverface), as well as Peavey® and Switchcraft®1/4' jacks. Does NOT fit the 24mm Marshall® pots.
Set of6 washers and 6 nuts.Part #JNUT-38-6$4.50(Set of 6 washers and 6 nuts)JACK NUT AND WASHER, METAL,SWITCHCRAFT®Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and theCTS or Alpha pots with 3/8' bushing (found on original vintage Fender®blackface and silverface), as well as Peavey® and Switchcraft®1/4' jacks. Does NOT fit the 24mm Marshall® pots.Part #JNUT-38$0.89(Set of 1 washer and 1 nut)Click on photo forlarger view. Jack is in the picture to demonstrate how the washersare installed - jack is NOT included with the washers.INSULATING SHOULDER WASHER, FIBERPair of fiber insulating shoulder washers for Switchcraft jacks with metalbushings. Used to mount standard jacks in a 1/2' diameter chassishole, while insulating the metal bushing (ground) of the jack from the chassis.ID 3/8', OD 1/2'.
Works great when replacing isolated plastic jacks with amore durable metal jack, which is frequently done on the input jacks of theFender® Hot Rod Deville/Deluxe and Blues Deville/Deluxe. Two washersare used on each jack, and the 'shoulders' are placed facing each other throughthe chassis.
The washers not only isolate the ground of the jackelectrically for noise reduction, but also stabilize the jack in the 1/2'diameter hole. Jack shown in picture NOT included. Workswell with the Switchcraft J-11, J-L11, J-12A, J-L12A, J-12B, J-L12B, J-13,J-13A, J-112APC, J-112BX, J-114BX, J-521 and J-524 jacks.Part #ISW-3069$0.49(For a pair of washers.
Each jack needs two washers.)Click on photo forlarger viewJACK, SPEAKON, CHASSIS-MOUNT -MADE FOR PC BOARD (SOLDER PINS).Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands,including Ampeg®.Part #J-NL4MD-V$4.95Click on photo forlarger viewJACK, SPEAKON, CHASSIS-MOUNT - MADE FORWIRE ATTACHMENT (3/16' PUSH ON CONNECTORS OR SOLDER TABS).Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands,including Ampeg®.Part #J-NL4MP$4.95Click on photo forlarger viewRevisit™ SPEAKER HARNESS COMPLETEWITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE FOR SINGLE SPEAKER. Preassembled for speaker cabinets with onespeaker. Includes Switchcraft #11 jack,and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-onspeaker connectors.
For two-speaker cabinets, see the SCH-2411X2,below.Part #SCH-2411$10.49Click on photo forlarger viewRevisit™ SPEAKER HARNESS COMPLETEWITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE FOR TWO SPEAKERCABINET. Preassembled for speaker cabinets with twospeakers in parallel. Includes Switchcraft #11 jack,and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-onspeaker connectors, plus an additional 24' jumper cable.Part #SCH-2411X2$14.99Click on photo forlarger viewRevisit™ SPEAKER HARNESS COMPLETEWITH 1/4' STRAIGHT PLUG and 24' SPEAKER WIRE FOR SINGLE SPEAKER. Preassembled for combo amps with onespeaker. Includes 1/4' straight plug,and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16'push-on speaker connectors.
For 2-speaker cabinets, add the SJ-150 jumper,below.Part #SCH-224$10.49Click on photo forlarger viewRevisit™ SPEAKER JUMPER CABLEpolyvinyl insulated silver plated copper speaker wire, 18 gauge, twisted pair,black and white. Terminated at each end in standard 3/16' speakerfast-on connectors. Great for connecting speakers in parallel in2x12 or 4x12 cabinets. 24 inches (61 cm) long. Made inUSA.Part #SJ-150$5.99Click on photo forlarger viewRevisit™ SPEAKER HARNESS COMPLETEWITH 1/4' RIGHT-ANGLE PL.
Never hurts to ask. AMpeg was an old company. SLM bought the name and whatever assets in 1986.
ANy files from the original AMpeg that did not make the trip won't be in company files. Same thing again in 2005 when Loud bought the brand from SLM. They got the files and assets from SLM, but any that got lost in the shuffle won't be available from them.And we sometimes find that a CSR at Loud might not realize that the schematic for the XYZ120 amp also contains the XYZ60. SO when someone calls for the XYZ60, they can't find it in their index, even though it is there.
They may learn those details over time, but I have run into that for people a number of times.And then there was that mysterious period when they were making them in Korea or VietNam or someplace, and no one seems to have documentation on those.
![](/uploads/1/2/7/5/127562103/539747836.png)